Router>enable
　　PassWord:
　　Password:
　　Password:
　　% Bad secrets
　　
　　Router>show version
　　Cisco Internetwork Operating System Software
　　IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
　　Copyright (c) 1986-1999 by cisco Systems, Inc.
　　Compiled Tue 07-Dec-99 02:21 by phanguye
　　Image text-base: 0x80008088, data-base: 0x80C524F8
　　
　　ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
　　
　　Router uptime is 3 minutes
　　System returned to ROM by abort at PC 0x802D0B60
　　System image file is "flash:c2600-is-mz.120-7.T"
　　
　　cisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.
　　Processor board ID JAB031202NK (3878188963)
　　M860 processor: part number 0, mask 49
　　Bridging software.
　　X.25 software, Version 3.0.0.
　　Basic Rate ISDN software, Version 1.1.
　　2 Ethernet/IEEE 802.3 interface(s)
　　2 Serial(sync/async) network interface(s)
　　1 ISDN Basic Rate interface(s)
　　32K bytes of non-volatile configuration memory.
　　8192K bytes of processor board System flash partition 1 (Read/Write)
　　8192K bytes of processor board System flash partition 2 (Read/Write)
　　
　　Configuration register is 0x2102
　　
　　Router>
　　!--- The router was just powercycled and during bootup a
　　!--- break sequence was sent to the router.
　　!
　　
　　*** System received an abort due to Break Key ***
　　
　　signal= 0x3, code= 0x500, context= 0x813ac158
　　PC = 0x802d0b60, Vector = 0x500, SP = 0x80006030
　　rommon 1 > confreg 0x2142
　　
　　You must reset or power cycle for new config to take effect
　　
　　rommon 2 > reset
　　
　　System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
　　Copyright (c) 1999 by cisco Systems, Inc.
　　TAC:Home:SW:IOS:Specials for info
　　C2600 platform with 32768 Kbytes of main memory
　　
　　
　　program load complete, entry point: 0x80008000, size: 0x6fdb4c
　　
　　Self decompressing the image : ###############################
　　##############################################################
　　##############################################################
　　##############################################################
　　############################### [OK]
　　
　　
　　Restricted Rights Legend
　　
　　Use, duplication, or disclosure by the Government is
　　subject to restrictions as set forth in subparagraph
　　(c) of the Commercial Computer Software - Restricted
　　Rights clause at FAR sec. 52.227-19 and subparagraph
　　(c) (1) (ii) of the Rights in Technical Data and Computer
　　Software clause at DFARS sec. 252.227-7013.
　　
　　cisco Systems, Inc.
　　170 West Tasman Drive
　　San Jose, California 95134-1706
　　
　　Cisco Internetwork Operating System Software
　　IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
　　Copyright (c) 1986-1999 by cisco Systems, Inc.
　　Compiled Tue 07-Dec-99 02:21 by phanguye
　　Image text-base: 0x80008088, data-base: 0x80C524F8
　　
　　cisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.
　　Processor board ID JAB031202NK (3878188963)
　　M860 processor: part number 0, mask 49
　　Bridging software.
　　X.25 software, Version 3.0.0.
　　Basic Rate ISDN software, Version 1.1.
　　2 Ethernet/IEEE 802.3 interface(s)
　　2 Serial(sync/async) network interface(s)
　　1 ISDN Basic Rate interface(s)
　　32K bytes of non-volatile configuration memory.
　　8192K bytes of processor board System flash partition 1 (Read/Write)
　　8192K bytes of processor board System flash partition 2 (Read/Write)
　　
　　
　　--- System Configuration Dialog ---
　　
　　Would you like to enter the initial configuration dialog? [yes/no]: n
　　
　　Press RETURN to get started!
　　
　　00:00:19: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up
　　00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
　　00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up
　　00:00:19: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
　　00:00:19: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
　　00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0, changed state to down
　　00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
　　Router>
　　00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to up
　　00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
　　00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down
　　00:00:50: %SYS-5-RESTART: System restarted --
　　Cisco Internetwork Operating System Software
　　IOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
　　Copyright (c) 1986-1999 by cisco Systems, Inc.
　　Compiled Tue 07-Dec-99 02:21 by phanguye
　　00:00:50: %LINK-5-CHANGED: Interface BRI0/0, changed state to administratively down
　　00:00:52: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administratively down
　　00:00:52: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down
　　00:00:52: %LINK-5-CHANGED: Interface Ethernet0/1, changed state to administratively down
　　00:00:52: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down
　　00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to down
　　00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to down
　　Router>
　　Router>enable
　　Router#copy startup-config running-config
　　Destination filename [running-config]?
　　1324 bytes copied in 2.35 secs (662 bytes/sec)
　　Router#
　　00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1, changed state to down
　　00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, changed state to down
　　Router#configure terminal
　　Enter configuration commands, one per line. End with CNTL/Z.
　　Router(config)#enable secret cisco
　　Router(config)#^Z
　　00:01:54: %SYS-5-CONFIG_I: Configured from console by console
　　Router#show ip interface brief
　　
　　Interface IP-Address OK? Method Status Protocol
　　Ethernet0/0 10.200.40.37 YES TFTP administratively down down
　　Serial0/0 unassigned YES TFTP administratively down down
　　BRI0/0 193.251.121.157 YES unset administratively down down
　　BRI0/0:1 unassigned YES unset administratively down down
　　BRI0/0:2 unassigned YES unset administratively down down
　　Ethernet0/1 unassigned YES TFTP administratively down down
　　Serial0/1 unassigned YES TFTP administratively down down
　　Loopback0 193.251.121.157 YES TFTP up up
　　Router#configure terminal
　　Enter configuration commands, one per line. End with CNTL/Z.
　　Router(config)#interface Ethernet0/0
　　Router(config-if)#no shutdown
　　Router(config-if)#
　　00:02:14: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
　　00:02:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up
　　Router(config-if)#interface BRI0/0
　　Router(config-if)#no shutdown
　　Router(config-if)#
　　00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
　　00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:2, changed state to down
　　00:02:26: %LINK-3-UPDOWN: Int

，重庆综合布线网络工程服务，重庆企业数据备份服务